Symetrix composer download previous versions

Click the unit that has the RS devices attached and select Properties. Select the RS Remote Control tab. Repeat steps 6 and 7 for each RS device connected to that unit.

In version 8. You will be able to open all previous version site files in version 8. However, files saved with version 8. If you intend to maintain both 8. A Backup all previous version design files. B Don't use the same file names for Version 8. C Choose the default locations when installing software.

D Do not use version 8. It is recommended that you backup your version 7. Even if all else goes completely wrong, as long as you have those files, there is a way to recreate your old setup. Note that once you save a file with Composer 8. If you are going to maintain both versions of the software on your PC, it is highly recommended that you include something in the file name of all previous version files you save to indicate their version.

This way you will be able to tell the files apart if they become co-mingled. Even if you are not going to maintain both versions, it is a good idea to use this practice at least until all your design files have been converted and you have fully embraced Version 8. When you install any version of Composer software, allow the installation to go to the default folder. This ensures that multiple versions will not interfere with each other. The versions of software and firmware must match! The only operation you should do that accesses hardware with mismatched software and firmware is to upgrade to the correct firmware.

Upgrading is generally possible regardless of the firmware mismatch. If this is not the case, the release notes will make a point of mentioning this. Procedure 1 — switched network or direct connection between only 2 units. Cable the Dante network as if it were in switched mode, not redundant mode. In other words, make connections only to the primary jack.

Alternately, if your do not have redundant-capable units that must be located through a DSP, you may simply disconnect the Dante network entirely.

If more than two devices are used without an external switch, you will need to use Procedure 2 below. Push on-line with the units. This will take slightly longer than usual as the Dante units change their mode.

Power down the units. Cable the Dante network as appropriate for the new mode. If switching to redundant mode, you may now connect the primary and secondary between two units or to separate switches. Power on the units. Again push on-line. Procedure 2 — daisy-chained connections.

Note that in a daisy-chained connection, only switched mode is supported. In your site file, disable everything except the first 2 units. In your site file, enable only the 2 connected unit. Push on-line. Repeat steps for all units. Skip to content What are you looking for? Hit enter to search Search. Support for using the T Glass in designs has been added. Many controls now support larger sizes on Control Screens. Over 65 additional improvements and enhancements.

For more Symetrix videos, please visit our YouTube channel. Installed Sound DSP. Optional AEC coprocessor… View. D Do not use version 7. It is recommended that you backup your version 7. Even if all else goes completely wrong, as long as you have those files, there is a way to recreate your old setup. Note that once you save a file with Composer 7. If you are going to maintain both versions of the software on your PC, it is highly recommended that you include something in the file name of all previous version files you save to indicate their version.

This way you will be able to tell the files apart if they become co-mingled. Even if you are not going to maintain both versions, it is a good idea to use this practice at least until all your design files have been converted and you have fully embraced Version 7. When you install any version of Composer software, allow the installation to go to the default folder. This ensures that multiple versions will not interfere with each other.

The versions of software and firmware must match! The only operation you should do that accesses hardware with mismatched software and firmware is to upgrade to the correct firmware.

Upgrading is generally possible regardless of the firmware mismatch. If this is not the case, the release notes will make a point of mentioning this. Procedure 1 — switched network or direct connection between only 2 units. Cable the Dante network as if it were in switched mode, not redundant mode. In other words, make connections only to the primary jack. Alternately, if your do not have redundant-capable units that must be located through a DSP, you may simply disconnect the Dante network entirely.

If more than two devices are used without an external switch, you will need to use Procedure 2 below. Push on-line with the units. This will take slightly longer than usual as the Dante units change their mode. Power down the units. Cable the Dante network as appropriate for the new mode.

If switching to redundant mode, you may now connect the primary and secondary between two units or to separate switches. Power on the units. Again push on-line. Procedure 2 — daisy-chained connections. Note that in a daisy-chained connection, only switched mode is supported.

In your site file, disable everything except the first 2 units. In your site file, enable only the 2 connected unit. Push on-line. Repeat steps for all units. Connect all units. Enable all units in your site file. Composer Version 7. I Changes from previous versions Changes in 7. It has the following changes, all relating to the T 1 An issue was resolved with blinking buttons that use custom images. Changes in 7. Main New 7. II Known Issues Issues related to VoIP 1 If a speed dial number is selected as the transfer target, the transfer will complete immediately as a blind transfer.

Other issues 18 Units may fail to pass Dante audio when switched vs. III Installation Notes If you are upgrading at an existing installation that loads a configuration automatically on start-up, the following procedure is recommended: 1.

Seattle, WA, USA Symetrix, manufacturer of high performance audio hardware and software for the installed sound market, has announced the release of the highly anticipated SymVue software for their Control Server hardware.

Have a question? Send us a note and someone will contact you right away to see how we can help you solve your greatest AV challenges brilliantly. Skip to content What are you looking for? Hit enter to search Search.